Products

Foster® Full Defense™ Fungicidal Protective Coating 40-25 is designed to eliminate any remaining mold and mildew after pre-cleaning contaminated surfaces. It also provides protection to various building materials, including unfinished wood, drywall, oriented strand board, metal, masonry, and more, safeguarding them from fungal growth.

Foster® Interior Defense™ Mold Resistant Coating (40-50) is specially formulated with select EPA-registered antimicrobial agents, ensuring long-term protection against odor-causing bacteria, mold, and mildew growth on its surface. This coating is ideal for use in various spaces, including attic spaces, wall cavities, crawl spaces, and floor joists, especially in areas where mold remediation has taken place. It is suitable for a wide range of applications, including industrial, commercial, residential, hospital, and school settings.

H.B. Fuller EV Therm 601 is a one-component UV curable technology that is thermally conductive, flame retardant, and electrically insulative. This material provides an optimum coating with a minimum coating thickness of 150 microns and encapsulation protection for electronic assemblies and components. This material was designed to be thermally conductive and is recommended for use with heatsinks, heat spreaders, cold plates, cooling tubes, and other thermal dissipation applications.

Foster® Eclipse™ Coating 40-11 is a low-odor, fast-setting, water-based surfacing material designed for field or shop application to faced or unfaced fiberglass duct liner or fiberglass duct board insulation. Its low viscosity enables application with a wide range of spray equipment available in the market.

HydroArmor® 7755 is a sprayable latex coating designed for use on aluminum, fiberglass, cold-rolled steel, galvanized steel, and most metal primers. HydroArmor® 7755 is formulated to give very good corrosion protection when applied as thinly as 20 mils wet. This low viscosity, sag-resistant coating can be easily sprayed onto exposed underbody areas and into restricted areas such as tubing and "hidden" areas accessible only with spray wands. Wet film builds of 30 mils or more can be applied without runs, drips, or sags.

TEC® LiquiDam™ Penetrating Moisture Vapor Barrier (213) is a low-viscosity, high-penetration, two-part, 100% solid epoxy. It is specially formulated to be applied to damp or new concrete, as little as 48 hours old, with a moisture vapor emission rate (MVER) less than or equal to 25 lbs. per 1,000 ft² per 24 hours (0.12 kg/m² per 24 hours) or a maximum relative humidity of 100%. It is designed to reduce the MVER to less than 3 lbs. per 1,000 ft² per 24 hours (0.015 kg/m² per 24 hours). LiquiDam™ is colored blue for visual assurance of coverage during the application process. Only one coat is required to penetrate and fill voids and gaps to fully seal the substrate, which quickly cures in as little as 4 - 5 hours to provide the benefit of same-day installation. LiquiDam™ is a moisture vapor barrier for the installation of floor coverings, tile, stone, and concrete toppings. Ideal for use with other TEC® adhesive, patch, underlayment, leveler, and mortar products.

Foster® 40-30C Protective Coating is a low-odor, fast-setting, water-based surfacing material intended for field or shop application to faced or unfaced fiberglass duct liner, fiberglass duct board insulation, or galvanized surfaces. Its low viscosity makes it suitable for application with a wide range of spray equipment currently available on the market.

HydroArmor® 7763 is a sprayable latex coating designed for use on aluminum, fiberglass, cold-rolled steel, galvanized steel, and most metal primers. It is formulated with additives to improve adhesion to oily metals. It provides very good corrosion protection, even when applied as thinly as 10 mils wet. This low-viscosity, sag-resistant coating can be easily sprayed onto exposed underbody areas and into restricted areas such as tubing and "hidden" areas accessible only with spray wands. Wet film builds of up to 20 mils can be applied without runs, drips, or sags.

Foster® 40-30™ Fungicidal Protective Coating is a low-odor, fast-setting, water-based surfacing material specifically crafted for field or shop application to faced or unfaced fiberglass duct liner, fiberglass duct board insulation, or galvanized surfaces. This formulation is highly effective at preventing the growth of mold and odor-causing bacteria on its surface for an extended period of time.

H.B. Fuller 20277 is a one-component, water-based fugitive adhesive and coating material designed for fast drying, clean machining, non-blocking, and excellent lay-flat and humidity resistance. It is suitable for spray, pattern, and extrusion applications and can be used to protect metals, fiberglass, contoured sheets, and other surfaces from weathering and discoloration during transportation.