SILAPRENE® Royal Seal 1000 Adhesive/Sealant DC13011

1 of 20 products in this brand
SILAPRENE® Royal Seal 1000 Adhesive/Sealant DC13011 is an exceptional one-part product that combines ease of application, versatility of use, high ultimate strength, permanent bonds and long service life. It is a high quality, elastomeric sealant that provides superior adhesion to a variety of surfaces.

Product Type: 1K (1 component) Adhesive, 1K (1 component) Sealant

Application Method: Gun

Compatible Substrates & Surfaces: Acrylonitrile Butadiene Styrene (ABS), Concrete, Elastomers & Rubbers, Epoxies, Fiberglass, Glass, Masonry, Metal, Phenolics, Plywood, Polyesters, Polyolefins, Polyurethane, Wood

Features: Acid Resistant, Chemical Resistant, Chipping Resistance, Crack Resistant, Fast Drying, Good Weather Fastness, Peel Resistance, UV Resistant, Water Resistant

Technical Data Sheet

Enhanced TDS

Identification & Functionality

Features & Benefits

Applications & Uses

Markets
Applications
Application Method
Compatible Substrates & Surfaces
Application Instructions

Preparation of substrates:

  • Surfaces to be bonded should be cleaned of all dust, oils or other contaminates. A solvent wipe is often adequate. Bonds to rigid surfaces are usually improved by a solvent wipe followed with light abrasion (180 grit), and another solvent wiping to remove abrasive residue. Dry surfaces thoroughly before applying adhesive.

Method of application:

  • Royal Seal Adhesive/Sealant can be applied by ordinary caulking guns or pressure pumping equipment. Pumping equipment should be of the follower-plate type and have a pump ratio of at least 40:1. Cox, Aro, Binks, DeVilbiss, Graco and Lincoln all produce suitable equipment for handling this material.
  • Apply a bead of Adhesive/Sealant to one surface at temperatures above 40°F. When used as an adhesive between two non-porous surfaces, solvent must escape through the edges of the bond line. Clamping, taping or use of mechanical fasteners to hold parts in place until Adhesive/Sealant develops strength is recommended.
  • After 24 hours at room temperature, the product is considered self-holding. The use of a heat lamp at 150°F for 1 hour will speed solvent evaporation and accelerate strength build-up.
  • Silaprene Royal Seal Adhesive/Sealant is formulated for room temperature curing, and curing is initiated when a majority of the solvent has been evacuated from the bond line. Strength build-up is very fast in the early stages to give high holding power, with continued strength build-up over time.

Method of application:

Uncured material can be cleaned up with VMP Naptha, Heptane, and Mineral Spirits. Thinning is not recommended. If a thinner product is deemed necessary for your application, contact your Royal Adhesives & Sealants salesman.

Properties

Soluble in
Aliphatic/Aromatic Hydrocarbons
Environmental Properties
ValueUnitsTest Method / Conditions
UV RatingLittle to no effect, 1000h-QUV test ASTM G53
Slump ResistanceGood--
Creep ResistanceExcellent--
Ozone ResistanceExcellent--
Elongation400.0%-
Typical Properties
ValueUnitsTest Method / Conditions
Solid Content65.0%-
ViscosityPaste extrusion grade--
Weight per Gallon8.05lb-
Specific Gravity0.97--
Temperature Range- 40 - 200°F-

Safety & Health

Precautionary Data

This product is flammable. Vapors may form an explosive mixture with air. Precautions should be taken to keep product away from fire, sparks, motors and other sources of heat or flame. Turn off or deactivate any electrical equipment or sources of ignition. Adequate ventilation is required to keep vapor concentrations below the Threshold Limit Value.

  • For professional or industrial ause only
  • Customer should determine ‘fitness for use’
  • Keep away from children
  • Keep container closed when not in use
  • Store closed container under 80°F

Storage & Handling

Shelf Life
12 Months