H.B. Fuller

Identification

GBU: BAS
RTU Product Type: Tape

Categories: Technologies → Adhesives & Sealants → Product Families → Pressure Sensitive Adhesives, Tapes & Labels → Tapes

Applications

Segment: Single Ply EPDM,

Flashing Sealant/Tape,

Flashing Tape

Applications & Uses

Application Guidelines

Clean entire surface where Millennium EPDM Self Adhered Curb Flashing will be applied.
Apply Millennium Single-Ply Primer or Millennium Primer 240 (LVOC) to entire surface to be covered using the supplied scrub pad. NOTE: Use caution when installing at temperatures below 40°F (4°C) to prevent blushing of EPDM primer (formation of condensation on surface of primer).
Allow the primer to dry to the touch (no material transfer, typically less than 20 minutes). Dry time will vary depending on ambient temperature and humidity.
Once the primer is dry immediately install Millennium EPDM Self Adhered Curb Flashing.
Position Self Adhered Curb Flashing over primed area and remove one side of perforated release liner at 45 degree angle while pressing down cover strip by hand. Repeat step with remaining poly covered tape of curb flashing on vertical surface.
Roll the Self Adhered Curb Flashing with a 2” (5.08cm) wide silicone roller.
Seal edges of Curb Flashing with patented Millennium EPDM Edge Sealant.*

Product Applications

Millennium EPDM Self Adhered Curb Flashing consists of a non reinforced cured 60 mil EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape. This tape is comprised of vulcanized rubber adhesive that will provide OEM quality performance for EPDM single-ply restoration projects.

Surface Preparation

All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface to receive the flashing with an approved EPDM membrane cleaner.

Features

Ready-to-Use Product Features: Flexible,

Heat Resistance,

High Durability,

High Moisture Resistance,

Resistance to UV lights,

Very Broad Seal Range,

Excellent Multi-Substrate Adhesion,

Quick Installation,

Reduces Labor Cost

Features & Benefits

Product Features

Resistant to UV light, high heat and moisture - Long-term durability
Excellent adhesion to multiple substrates - Suitable for a wide variety of sealing applications
Fast installation - Saves time and labor
18” tape width - Suitable for EPDM curb flashing and detail applications

Packaging & Availability

Regional Availability

North America

Packaging Information

Millennium EPDM Self Adhered Curb Flashing with perforated poly release liner is available in the following sizes:

North America

Width	Length	Part #	Rolls/Case
18 inch (457mm)	48 ft. (14.6m)	ET-0584-18	1

Europe, Cis, and Middle East

Width	Length	Part #	Rolls/Case
18 inch (457mm)	48 ft. (14.6m)	ET-0584-18EU	1

Properties

Strain at Break:

300.0 %

Tear Strength:

21.875 kN/m

Tensile Strength:

6.21 MPa

Note

The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.

Typical Properties


	Value	Units	Test Method / Conditions
Base Polymer	Ethylene Propylene Diene Monomer	-	Fourier Transform Infrared Spectroscopy
Brittle Point	-46	°C	ASTM D2137
Elongation	300	%	ASTM D412
Ozone Resistance	No cracking	-	ASTM D4419
Peel Strength (at 21°C)	min. 8	pli	ASTM D413
Shear Strength (at 21°C)	min. 20	psi	ASTM D816
Storage Temperature	40 - 110	°F	-
Tear Strength	125	lb/in	ASTM D624
Tensile Strength (die c)	min. 900	psi	ASTM D412

Storage & Handling

Storage and Shelf Life Conditions: Store material in original unopened packaging at temperatures between 40°F-110°F (4°C - 43°C). Shelf life is 24 months when stored as recommended.
Shelf Life: 24 months

Millennium EPDM Self Adhered Curb Flashing

Enhanced TDS