Millennium EPDM High-Tack Primer

1 of 41 products in this brand
Millennium EPDM High-Tack Primer is a rubber polymer-based roofing primer. The high viscosity formulation promotes uniform coverage on both horizontal and vertical surfaces. It is used to prime EPDM roofing membrane to provide improved adhesion to the Millennium family of EPDM tapes, laminates, and sealants. Millennium EPDM High-Tack Primer is an excellent choice for priming concrete, OSB, plywood, and metal surfaces.

Product Type: Primer

Application Area: Roofing Substrates

Compatible Substrates & Surfaces: Concrete, Metal, Wood

Features: Fast Drying, High Coverage, High Durability, High Viscosity, Improved Adhesion, Tacky

Chemical Family: Ethylene-Propylene-Diene Copolymers (EPDM)

Technical Data Sheet

Enhanced TDS

Identification & Functionality

Features & Benefits

Ready-to-Use Product Features
Key Attributes
Features Benefits
High viscosity formula

Provides uniform coverage, no running or puddling

Fast drying

Speeds Installation

Unique polymeric formulation

Long-term durability

Dual function primer

Holds seam in fold-back position while priming

Applications & Uses

Markets
Applications
Application Area
Compatible Substrates & Surfaces
Basic Use

Millennium EPDM High-Tack Primer is used to prime EPDM roofing membrane to provide improved adhesion to the Millennium family of EPDM tapes, laminates, and sealants. Millennium EPDM High-Tack Primer is an excellent choice for priming concrete, OSB, plywood, and metal surfaces.

In addition to seam priming, Millennium EPDM High-Tack Primer is used to hold EPDM membrane in a folded back position while seam priming is completed.

Surface Preparation

All work surfaces should be clean, dry, free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and othercontaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface with an approved EPDM membrane cleaner prior to application of Millennium EPDM High-Tack Primer.

Limitations
  • Do not use as a membrane cleaner.
  • Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion.Clean and dry surfaces are a necessity.
  • Not for use on PVC or TPO roof membranes.
  • Do not use on extruded or expanded polystirene insulation.
  • At Installation temperatures below 40°F (4°C) care must be taken to prevent the formation of condensation on surface of primer.
  • Not for use in VOC regulated markets.
  • Once opened, primer should be used completely. Storage life is limited after opening.
Application Method

1. Thoroughly shake or stir Millennium EPDM High-Tack Primer prior to use and re-stir every 15-20 minutes during use.
2. Do not dilute Millennium EPDM High-Tack Primer.
3. Surfaces should be dry and clean before applying Millennium EPDM High-Tack Primer. If necessary, clean the surface with an approved EPDM membrane cleaner prior to application of Millennium EPDM High-Tack Primer. Observe all manufacturers’ safety precautions and use recommendations when using solvents. Do not smoke while working with primer.
4. When the surfaces are dry, apply Millennium EPDM High-Tack Primer with a fully saturated brush or scouring pad. The surface should appear wet during application. Apply primer
to a wider area then the actual bonding area to insure complete coverage. If using a scouring pad, be sure that it is free of excessive dust from EPDM membranes. Replace pads often. Do not overwork primer.
5. Allow primer to dry completely (typically less than 20 minutes) before applying tape/flashing materials. Primer will visually appear shiny and tacky to the touch. Drying conditions will vary depending on ambient air conditions. NOTE: Use caution when installlling at temperatures below 40°F (5°C) to prevent blushing of EPDM primer (formation of condensation on surface of primer).
6. When not in use, keep lid on primer to prevent solvent evaporation. When finished, secure lid and store primer as recommended. Once opened, primer has a limited use life.
7. Once the seam or flashing is installed the primer will take up to 48 hours to wet-out the tape surface and build full strength. Any peel tests on installed seams or flashings should not be conducted until at least 24 hours after installation.
8. For areas where Millennium EPDM High-Tack Primer is used in a tack-back application; apply primer to surface of membrane, allow primer to dry and then fold back membrane to make contact with primed area. Lightly apply pressure to ensure membrane holds in desired position while primer is applied to seam and flashing areas.

Equipment Clean up

Use Mineral Spirits or VM&P naptha. Observe all manufacturer’s safety precautions and use recommendations when using solvents.

Properties

Typical Physical Properties
ValueUnitsTest Method / Conditions
Solids Content15%-
Weight6.74lbs/gal-
VOC Content685.0g/L-
Application Temperaturemin. 50°F-
Note

The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.

Packaging & Availability

Regional Availability
  • Australia & New Zealand (ANZ)
  • Latin America
  • North America
  • South East Asia
Packaging and Coverage

Millennium EPDM High-Tack is available in the following package:

Container Size Containers/Case
1 gallon (3.8L) 4

Coverage rates will be approximately 250 - 400 ft2 per gallon (23.2 - 37 m2 per liter).

Storage & Handling

Shelf Life
12 Months
Storage Conditions

Store material in original unopened containers at temperatures between 40°F - 90°F (4°C - 32°C). Shelf life is 12 months when stored in unopened container.