H.B. Fuller 5005 is a single-component, low-viscosity ethoxyethyl cyanoacrylate adhesive. It is designed for applications where vapor control is an issue, thanks to its low-odor and non-blooming characteristics. H.B. Fuller 5005 is certified to ISO 10993-5 for biocompatibility, making it suitable for use in medical device applications.

Product Type: 1K (1 component) Adhesive, Anaerobic Adhesive

Application Area: Medical Devices

Chemical Family: Cyanoacrylates

Features: Excellent Part Finish (Low Bloom), Low Blooming, Low Odor, Low Viscosity, Solvent Resistance

Technical Data Sheet

Enhanced TDS

Identification & Functionality

Features & Benefits

Applications & Uses

Markets
Applications
Application Area
Cure Method
General Instructions

Surfaces to be bonded should be clean and dry. Dispense a drop or drops to one surface only. Apply only enough to leave a thin film layer after compression. Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less that one minute and maximum strength is attained in 24 hours. Wipe off excess adhesive from the top of the container and recap. products if left uncapped may deteriorate by contamination from moisture in the air. Because products cure by polymerization, whitening may appear on the surface of the container or the bonded materials. This will not affect adhesive performance.

Properties

Physical Form
Appearance
Clear
Typical Properties
ValueUnitsTest Method / Conditions
Shear Strength***2600.0psi-
Temperature Range-67 to 203°F-
Fixture Time15.0sec-
Technical Data
ValueUnitsTest Method / Conditions
Specific Gravity1.06--
Cured Properties
ValueUnitsTest Method / Conditions
Service Temperature- 55 - 95°C-
Full Cure Time24.0h-
Cure AppearanceClear--
Uncured Properties
ValueUnitsTest Method / Conditions
Flash Point80.0°C-
Set Time (Ethylene Propylene Diene Monomer)5.0s-
Set Time (Steel)15.0s-
Set Time (Acrylonitrile Butadiene Styrene)10.0s-
Rheological Properties
ValueUnitsTest Method / Conditions
Viscosity2 - 6cPBrookfield SC4-21
Note
*** Performance of cured adhesive on Stainless Steel

Regulatory & Compliance

Certifications & Compliance

Technical Details & Test Data

Curing Performance

Ambient surface moisture initiates the curing process. Handling strength is reached in a short time, and will vary based on environmental conditions, bond line gap, and other factors. Product will continue to cure for at least 24 hours before full strength and solvent resistance is developed.

Time Until Full Cure (% of RT strength)

H.B. Fuller 5005 - Time Until Full Cure (% of Rt Strength)

Performance Range by Substrate (N/mm²)

H.B. Fuller 5005 - Performance Range By Substrate (N/Mm²)

Heat Aging (aged at temperature indicated and tested at 22°C)

H.B. Fuller 5005 - Heat Aging (Aged At Temperature Indicated And Tested At 22°C)

Hot Strength (%RT strength, tested at temperature)

H.B. Fuller 5005 - Hot Strength (%Rt Strength, Tested At Temperature)

Performance of Cured Adhesive
Substrate N/mm² PSI
Steel 11.0 to 20.1 1600 to 2920
AL 13.9 to 15.4 2020 to 2240
PC** 6.5 to 8.6 940 to 1250
PVC** 3.3 to 7.3 485 to 1055
ABS** 4.0 to 5.3 580 to 765

 

*Rubber figures given are typical. Your results may vary by specific rubber type.
**Tested to ASTM 4501
***n/r = not recommended

Solvent Resistance
Solvent Example Resistance
Alcohol

Ethanol, Methanol

+ + +
Ester (aromatic) Ethylacetate + + +
Ketone (aromatic)

Acetone, Benzophenone

– – –
Aliphatic hydrocarbon (alkanes)

Petrol, Heptanes, Hexane

+ + –
Aromatic hydrocarbons

Benzyl, Toluol, Xylol

+ + –
Halogenated hydrocarbons

Methylenchloride, Chloroform, Chlorobenzol

– – –
Weak aqueous

Nitrite, muriatic acid, sulphuric acid, phosphoric acid

+ + + (– – – if concentrated)
Weak aqueous base

sodium hydroxide solution, caustic potash

+ + + (– – – if concentrated)

Packaging & Availability

Country Availability
Regional Availability
  • Africa
  • Asia Pacific (Excluding Russia)
  • Europe (Excluding Russia)
  • India
  • Latin America
  • Middle East
  • North America

Storage & Handling

Shelf Life
12 Months
Storage Conditions

Containers should be stored in a cool, dry, dark area. Storage temperature 15.5°C - 25°C (60°F - 77°F), without exposure to direct light or heat. Do not refrigerate.