Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Compatible Substrates & Surfaces
- Application Instructions
Surface Preparation: Grout joints must be clean, dry, free of dirt and dust. Wipe down vinyl tile surface with a slightly dampened sponge before grouting.
Application
- Grout no more than 10 sq. ft. (0.93 m2) at a time.
- Press grout diagonally into joints holding float at a 45-degree angle. Make sure that joints are completely filled
- Remove all excess grout off vinyl tile by holding float at a 90-degree angle and drawing diagonally across tile.
- To clean, first soak sponge in cool clean water. Wring out completely.
- Use the damp sponge in a light, circular motion to smooth joints and clean film from the vinyl tile. Avoid using excessive amounts of water on the grout joints.
- Turn sponge over to a clean side and draw diagonally across vinyl tiles to remove any remaining film.
- Wait 10 minutes, then buff vinyl tile with a soft clean cloth to remove remaining grout film.
- There is no need to seal TEC® Premixed Vinyl Tile Grout.
Note: If excess water is used in the sponge during clean up, minor cracks or pinholes can develop. If the grout is over-worked, it may appear to shrink down into joint. Should this occur, simply apply a second coat to the affected areas. You must allow your initial application to cure for 24 hours prior to your second application.
- Existing Grout Repairs: Completely remove existing grout from the joints. Do not damage vinyl tile. Vacuum dust from vinyl tile surface and grout joints. Follow application instructions.
- Set-up Time: Light foot traffic after 24 hours. Allow 7 days to achieve final cure which includes hardness and stain resistance. Allow 7 days before exposure to water.
- Clean-up: Clean tools and hands with warm soapy water while grout is still wet.
- Maintenance: After 7 day cure, routine cleaning of your grout can be done by using a Neutral pH cleaner. Follow manufacturer instructions for dilution. Do not use acids, bleaches or vinegar for cleaning.
- Limitations
- Not for exterior use.
- Do not apply in temperatures below 50°F (10°C) or above 90°F (32°C).
- Not for use in grout joints wider than 1⁄4 inch (6 mm).
- Do not add water.
- Keep from freezing.
- Keep at room temperature for 24 hours prior to use.
Properties
- Physical Form
- Physical Properties
Value Units Test Method / Conditions Final Cure (Full stain and water resistance) 7 Days - Light Foot Traffic (at 22°C) 24.0 Hours - VOC/Liter of Material 15 grams - Foot Traffic Rating Residential - ASTM C627
Packaging & Availability
- Packaging Type
- Packaging and Coverage
1⁄2 gallon plastic pail (1.89 L)
Coverage: Figures shown in the chart are presented only as guidelines.
Approximate Coverage per 1⁄2 gallon (1.89 L) Vinyl Tile Size Joint Width 1⁄8"
(3 mm)3⁄16"
(4.5 mm)1⁄4"
(6 mm)12" x 12"
(300 mm x 300 mm)300 sq. ft.
(27.8 m2)200 sq. ft.
(18.6 m2)150 sq. ft.
(13.9 m2)18" x 18"
(450 mm x 450 mm)450 sq. ft.
(41.8 m2)300 sq. ft.
(27.8 m2)225 sq. ft.
(20.9 m2)
Storage & Handling
- Shelf Life
- max. 1 year
- Storage & Shelf Life
- Store indoors in a cool, dry location. Keep away from excessive heat. Keep from freezing. If frozen, slowly bring material back to room temperature and mix per instructions.
- Shelf Life: Maximum of 1 year from date of manufacture in unopened package. Product good for 6 months after opening as long as bucket is re-sealed carefully and stored in a cool, dry, interior location and used within shelf life. Covering with plastic wrap directly on top of product prior to sealing container will help preserve freshness.