Millennium Primer 240
1 of 52 products in this brandRTU Product Type: Primer, Solventborne Adhesive
Application Area: Laminates, Roofing Membranes, Roofing Substrates
Compatible Substrates & Surfaces: Concrete, Ethylene Propylene Diene Monomer (EPDM), Metal, Oriented Strand Board (OSB), Plywood, Thermoplastic Polyolefin (TPO), Wood
Features: Good Bond Strength, High Performance, Improved Adhesion, Low VOC, Reusable, Solvent-Based, UL Listed
Enhanced TDS
Identification
- Country of Origin
- GBU
- RTU Product Type
- Categories
Applications
- Application Area
- Compatible Substrates & Surfaces
- Segment
Applications & Uses
- Application Instructions
-
Surface Preparation: All work surfaces should be clean, dry, free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface with an approved EPDM or TPO membrane cleaner prior to application of Millennium Primer 240.
Equipment Clean-up: Use Mineral Spirits or VM&P naptha. Observe all manufacturer’s safety precautions and use recommendations when using solvents.
- Thoroughly shake or stir Millennium Primer 240 prior to use and re-stir every 15-20 minutes during use. Note: product may exhibit an “apple sauce” type texture even after agitation. This appearance is normal and will not adversely affect the product’s performance. For more information on primer appearance, see Millennium Single-Ply Primer Appearance Technical Bulletin.
- Do not dilute or extend Primer 240 with any liquids.
- Surfaces should be dry, clean and free of any loose debris before applying Primer 240. Aged waterproofing membrane should be pressure washed and dried completely before applying Primer 240. Observe all Manufacturers’ safety precautions and use recommendations when using solvents.
- When the surfaces are dry, apply Millennium Primer 240 with a fully saturated brush or scouring pad. The surface should appear wet during application. Apply primer to a wider area then the actual bonding area to insure complete coverage. If using a scouring pad, be sure that it is free of excessive dust from EPDM membranes. Replace pads often. Do not overwork primer.
- Allow primer to dry completely (typically within 30 to 40 minutes) before applying tape. Primer will visually appear “dull” or “flat” and will feel dry to the touch. Drying conditions will vary depending on ambient air conditions. NOTE: Use caution when installlling at temperatures below 40oF (5oC) to prevent blushing of EPDM primer (formation of condensation on surface of primer). Drying time may significantly increase at low temperatures.
- When not in use, keep lid on primer to prevent solvent evaporation. When finished, secure lid and store primer as recommended for use at a later date.
- Once the seam or flashing is installed the primer will take up to 48 hours to wet-out the tape surface and build full strength. Any peel tests on installed seams or flashings should not be conducted until at least 24 hours after installation. For more information, please see H.B. Fuller’s Technical Bulletin on Cool Cover™ TPO Adhesion Strength.
- Basic Use
-
Millennium Primer 240 is used to prime EPDM and TPO roofing membrane to provide improved adhesion to the Millennium family of EPDM tapes, laminates, and sealants as well as H.B. Fuller’s Cool Cover™ line of TPO tapes, laminates, and sealants. Millennium Primer 240 is an excellent choice for priming concrete, OSB, plywood, and metal surfaces.
- Limitations
-
- Do not use as a membrane cleaner.
- Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion.
- Clean and dry surfaces are a necessity.
- Not for use on PVC or KEE roof membranes.
- Do not use on extruded or expanded polystirene insulation.
- Packaging and Coverage
-
Millennium Primer 240 is available in the following package:
Container Size Part # Packaging 1 quart (0.9L) CN-5781-QT 6 quarts/case 1 gallon (3.8L) CN-5781 6 pails/case 3 gallon (11.4L) BK-5781-3 30 pails/pallet Coverage rate will be approximately 200-225 sq. ft. per gallon (18.6-20.9 m2 per liter).
Features
- Ready-to-Use Product Features
Features & Benefits
- Key Attributes
-
Features Benefits VOC less than 250 g/L Useful in regulated markets High performance Maintains bond strength after environmental exposures Unique polymeric formulation Provides excellent adhesion to a variety of substrates (EPDM, TPO, metals, wood, and concrete) Reusable Reduces waste
Identification & Functionality
- Product Image
-
Packaging & Availability
- Packaging Type
- Regional Availability
Physical Properties
- Physical Form
- Appearance
-
Translucent free flowing liquid
Properties
- Application Temperature:
-
-18~43 °C
- Shelf Life:
-
18 months
- Solid Content:
-
10 %
- Viscosity:
-
600 cps
- VOC Calculation
-
The VOC content of this primer was determined under Rule 1168 for low solids adhesive primer. The calculation is determined as follows:
VOC content = (Ws-Ww-Wex) / Vm
Where:- Solids: <120 g/l
- Ws = weight of volatile compounds in gm
- Ww = weight of water in gm
- Wex = Weight of exempt compounds in gm
- Vm = volume of material in liters
- Typical Properties
-
Value Units Test Method / Conditions Application Temperature -18 to 43 °C - Coverage 200 - 225 ft²/gal - Storage Temperature 4 - 32 °C - - Typical Physical Properties
-
Value Units Test Method / Conditions Creep Displacement (at 70°C, 300g load) max. 0.125 inch - Density 9.86 lb/gal - Solid Content 10 % - Viscosity 600 cPs Brookfield Viscometer Volatile Organic Compound Content max. 250 g/L Internal Test Method - Appearance
-
Translucent free flowing liquid
Storage & Handling
- Storage Information
-
Store material in original unopened containers at temperatures between 40°F - 90°F (4°C - 32°C). Shelf life is 18 months when stored in unopened container.
- Shelf Life
-
18 months