Enhanced TDS
Identification & Functionality
- Backing Material Type
- Product Type
- Technologies
- Product Families
- Base Polymer (Flashing & Tape)
- Base - EPDM
- Test Method - FTIR
Features & Benefits
- Ready-to-Use Product Features
- Key Attributes
Features Benefits Resistant to UV light, high heat and moisture Long-term durability
Excellent adhesion formability Flashing details with proven peel & stick technology
No torch or liquid adhesives Improved safety Fast Installation Saves time and labor
Waterproof detail Suitable for roofing, pond lining, and waterproofing applications
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Basic Use
Millennium EPDM Flashing Tapes are ideal for flashing rooftop penetrations and other details such as:
- Overlay at T-joints, corners, pipes, and penetrations
- General repair in non-traffic areas
- Gravel stop flashing
- General purpose flashing
- Metal edge tie-in
- Surface Preparation
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface to receive the flashing with an approved EPDM membrane cleaner.
- Limitations
- Not for use on PVC roof membranes.
- Not for use in high traffic areas.
- Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion.
- Clean and dry surfaces are necessary for proper Installation of this product.
- Application Method
1. Clean entire surface where Millennium EPDM Flashing Tape will be applied.
2. Apply EPDM primer to entire surface to be covered using the supplied scrub pad. NOTE: Use caution when installlling at temperatures below 40°F (4°C) to prevent blushing of EPDM
primer (formation of condensation on surface of primer).
3. Allow the primer to dry to the touch (no material transfer, typically less than 20 minutes). Dry time will vary depending on ambient temperature and humidity.
4. Once the primer is dry immediately install Millennium EPDM Flashing Tape.
5. Position Flashing Tape over primed area and remove release liner. Press down and form Flashing Tape by hand.
6. Roll the flashing with a 2” (5.08cm) wide silicone roller.
7. Seal edges of flashing detail with patented Millennium EPDM Edge Sealant.**US 6,642,296 B2; US 6,291,571 B1
Properties
- Color (Properties)
- Typical Properties
Value Units Test Method / Conditions Tensile Strength (Uncured) max. 250 psi ASTM D 412 Die C Elongation (Uncured) min. 600 % ASTM D 412 Ozone Resistance No Cracking - ASTM D 1149 Peel Strength (at 21°C) 10.0 pli ASTM D 413 Shear Strength (at 21°C) 20.0 psi ASTM D 816 Brittleness Temperature -46 °C ASTM D 2137 - Note
The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.
Packaging & Availability
- Packaging Type
- Regional Availability
- Packaging and Coverage
Millennium EPDM Flashing Tape is available in the following sizes:
North America :
Width Length Part # Rolls/Case 5 inch (127mm) 100 ft. (30.48m) ET-0553-05 2 6 inch (152mm) 100 ft. (30.48m) ET-0553-06 2 9 inch (229mm) 50 ft. (15.24m) ET-0553-09 2 12 inch (305mm) 50 ft. (15.24m) ET-0553-12 1 18 inch (458mm) 50 ft. (15.24m) ET-0553-18 1 Europe, CIS and Middle East
Width Length Part # Rolls/Case 5 inch (127mm) 100 ft. (30.48m) ET-0553-05EU 2 6 inch (152mm) 100 ft. (30.48m) ET-0553-06EU 2 9 inch (229mm) 50 ft. (15.24m) ET-0553-09EU 2 12 inch (305mm) 50 ft. (15.24m) ET-0553-12EU 1 18 inch (458mm) 50 ft. (15.24m) ET-0553-18EU 1
Storage & Handling
- Shelf Life
- 9 Months
- Storage Conditions
Store material in original unopened packaging at temperatures between 40°F-110°F (4°C - 43°C). Shelf life is 9 months when stored as recommended.