Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Cure Method
- General Instructions
Surfaces to be bonded should be clean and dry. Dispense a drop or drops to one surface only. Apply only enough to leave a thin film layer after compression. Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less that one minute and maximum strength is attained in 24 hours. Wipe off excess adhesive from the top of the container and recap. products if left uncapped may deteriorate by contamination from moisture in the air. Because products cure by polymerization, whitening may appear on the surface of the container or the bonded materials. This will not affect adhesive performance.
Properties
- Color (Properties)
- Physical Form
- Appearance
- Translucent
- Typical Properties
Value Units Test Method / Conditions Shear Strength*** 2730.0 psi - Temperature Range -67 to 203 °F - Fixture Time 50.0 sec - - Technical Data
Value Units Test Method / Conditions Specific Gravity 1.06 - - - Cured Properties
Value Units Test Method / Conditions Service Temperature - 55 - 95 °C - Full Cure Time 24.0 h - Cure Appearance Gel - - - Uncured Properties
Value Units Test Method / Conditions Flash Point 85.0 °C - Set Time (Ethylene Propylene Diene Monomer) 15.0 s - Set Time (Steel) 50.0 s - Set Time (Acrylonitrile Butadiene Styrene) 18.0 s - - Rheological Properties
Value Units Test Method / Conditions Viscosity 9500 - 20500 cP -
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Curing Performance
Ambient surface moisture initiates the curing process. Handling strength is reached in a short time, and will vary based on environmental conditions, bond line gap, and other factors. Product will continue to cure for at least 24 hours before full strength and solvent resistance is developed.
- Time Until Full Cure (% of RT strength)
- Performance Range by Substrate (N/mm²)
- Heat Aging (aged at temperature indicated and tested at 22°C)
- Hot Strength (%RT strength, tested at temperature)
- Performance of Cured Adhesive
Substrate N/mm² PSI Steel 13.8 to 18.8 2000 to 2730 Rubber* 4.3 to 15.2 630 to 2200 AL 10.4 to 13.2 1510 to 1920 PC** 22.3 to 24.9 3240 to 3605 PVC** 18.3 to 26.7 2660 to 3875 ABS** 12 to 18.3 1740 to 2660 *Rubber figures given are typical. Your results may vary by specific rubber type.
**Tested to ASTM 4501
***n/r = not recommended- Solvent Resistance
Solvent Example Resistance Alcohol Ethanol, Methanol
+ + + Ester (aromatic) Ethylacetate + + + Ketone (aromatic) Acetone, Benzophenone
– – – Aliphatic hydrocarbon (alkanes) Petrol, Heptanes, Hexane
+ + – Aromatic hydrocarbons Benzyl, Toluol, Xylol
+ + – Halogenated hydrocarbons Methylenchloride, Chloroform, Chlorobenzol
– – – Weak aqueous Nitrite, muriatic acid, sulphuric acid, phosphoric acid
+ + + (– – – if concentrated) Weak aqueous base sodium hydroxide solution, caustic potash
+ + + (– – – if concentrated)
Storage & Handling
- Shelf Life
- 12 Months
- Storage Conditions
Containers should be stored in a cool, dry, dark area. Storage temperature 15.5°C - 25°C (60°F - 77°F), without exposure to direct light or heat. Do not refrigerate.