Millennium EPDM Flashing Tape
1 of 33 products in this brandRTU Product Type: Tape
Application Area: Joints, Pipes, Roofing Substrates, Roofs
Compatible Substrates & Surfaces: Composites, Wood
Features: Excellent Formability, Excellent Substrate Adhesion, Flexible, Good Adhesion, Good Shrinkage Resistance, Heat Resistance, High Durability, Moisture Resistant, Resistance to UV lights
Enhanced TDS
Identification
- Backing Material
- GBU
- RTU Product Type
- Categories
Applications
- Application Area
- Compatible Substrates & Surfaces
- Segment
Applications & Uses
- Application Method
-
1. Clean entire surface where Millennium EPDM Flashing Tape will be applied.
2. Apply EPDM primer to entire surface to be covered using the supplied scrub pad. NOTE: Use caution when installlling at temperatures below 40°F (4°C) to prevent blushing of EPDM
primer (formation of condensation on surface of primer).
3. Allow the primer to dry to the touch (no material transfer, typically less than 20 minutes). Dry time will vary depending on ambient temperature and humidity.
4. Once the primer is dry immediately install Millennium EPDM Flashing Tape.
5. Position Flashing Tape over primed area and remove release liner. Press down and form Flashing Tape by hand.
6. Roll the flashing with a 2” (5.08cm) wide silicone roller.
7. Seal edges of flashing detail with patented Millennium EPDM Edge Sealant.**US 6,642,296 B2; US 6,291,571 B1
- Basic Use
-
Millennium EPDM Flashing Tapes are ideal for flashing rooftop penetrations and other details such as:
- Overlay at T-joints, corners, pipes, and penetrations
- General repair in non-traffic areas
- Gravel stop flashing
- General purpose flashing
- Metal edge tie-in
- Limitations
-
- Not for use on PVC roof membranes.
- Not for use in high traffic areas.
- Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion.
- Clean and dry surfaces are necessary for proper Installation of this product.
- Surface Preparation
-
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface to receive the flashing with an approved EPDM membrane cleaner.
Features
- Ready-to-Use Product Features
Features & Benefits
- Key Attributes
-
Features Benefits Resistant to UV light, high heat and moisture Long-term durability
Excellent adhesion formability Flashing details with proven peel & stick technology
No torch or liquid adhesives Improved safety Fast Installation Saves time and labor
Waterproof detail Suitable for roofing, pond lining, and waterproofing applications
Identification & Functionality
- Base Polymer (Flashing & Tape)
-
- Base - EPDM
- Test Method - FTIR
Packaging & Availability
- Packaging Type
- Regional Availability
- Packaging and Coverage
-
Millennium EPDM Flashing Tape is available in the following sizes:
North America :
Width Length Part # Rolls/Case 5 inch (127mm) 100 ft. (30.48m) ET-0553-05 2 6 inch (152mm) 100 ft. (30.48m) ET-0553-06 2 9 inch (229mm) 50 ft. (15.24m) ET-0553-09 2 12 inch (305mm) 50 ft. (15.24m) ET-0553-12 1 18 inch (458mm) 50 ft. (15.24m) ET-0553-18 1 Europe, CIS and Middle East
Width Length Part # Rolls/Case 5 inch (127mm) 100 ft. (30.48m) ET-0553-05EU 2 6 inch (152mm) 100 ft. (30.48m) ET-0553-06EU 2 9 inch (229mm) 50 ft. (15.24m) ET-0553-09EU 2 12 inch (305mm) 50 ft. (15.24m) ET-0553-12EU 1 18 inch (458mm) 50 ft. (15.24m) ET-0553-18EU 1
Physical Properties
- Color (Properties)
Properties
- Shelf Life:
-
9 months
- Strain at Break:
-
600 %
- Tensile Strength:
-
1.725 MPa
- Note
-
The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.
- Typical Properties
-
Value Units Test Method / Conditions Base Polymer Ethylene Propylene Diene Monomer - Fourier Transform Infrared Spectroscopy Brittle Point -46 °C ASTM D2137 Elongation (uncured) min. 600 % ASTM D412 Ozone Resistance No cracking - ASTM D1149 Peel Strength (at 21°C) 10 pli ASTM D413 Shear Strength (at 21°C) 20 psi ASTM D816 Storage Temperature 4 - 43 °C - Tensile Strength (uncured, die c) max. 250 psi ASTM D412
Storage & Handling
- Storage Conditions
-
Store material in original unopened packaging at temperatures between 40°F-110°F (4°C - 43°C). Shelf life is 9 months when stored as recommended.
- Shelf Life
-
9 months