UltraShield HY 17

Identification

Chemical Family

Polyurethanes (PU)

GBU

BAS

RTU Product Type

Hybrid Coating,

Waterborne Coating

Categories

Markets → Building & Construction → Applications → Building Envelope & Roofing → Waterproofing & Weatherproofing

Markets → Building & Construction → Applications → Building Materials → Structural Components

Markets → Paints & Coatings → Applications → Building & Construction → Roof Coatings

Technologies → Ready-to-Use Products → Product Families → Paints & Coatings → Protective Coatings

Applications

Application Area

Sandwich Panels,

Kitchen,

Patios,

Roofs,

Shower,

Balconies,

Terraces

Compatible Substrates & Surfaces

Metal,

Aluminum,

Asbestos,

Concrete

Applications & Uses

Application Procedure

Surface Preparation: The substrate on which the coating will be applied has to be cleaned thoroughly of all contaminants which may affect the adhesion. This can be done by grit blasting or at least using a wire brush rigorously. All major repair works needs to be carried out with a suitable repair material prior to the application.
 

Priming: UltraShield HY 17 can be applied directly onto the concrete surface. If the surface is highly porous, a primer coat is required, using a brush or roller to seal the pores and stabilize the surface by diluting UltraShield HY 17 with water (1:1 ratio). This will help in boosting adhesion for the top coat. Primer application should be done at a coverage rate of 5m2/l. Allow the primer to become dry prior to the application of the top coat.

Mixing: To ensure a homogenous mix, it is recommended to mix the contents of the pail prior to the application, to remove any sediments which may have occurred during storage. A paddle mixer can be used for mixing.

Application: Apply each coat of UltraShield HY 17 at a coverage rate of 0.85 kg/m2 to attain a Dry Film Thickness of 0.4mm. A total of 0.8mm thickness will be achieved in two coats.
For best results, apply the coating with a brush or a roller. Corners and joints shall be treated with a fibre mesh to provide added strength to the applied coating. This mesh shall be applied immediately on the 1st coat whilst it is still wet. The second coat should be applied cross wise after the first coat dries off completely, provide a re-coat interval of around 6 hours.

Curing: The coating shall be cured fully for 7 days to achieve its full mechanical properties, after which it can be put to use.

View Synonyms and Definitions

Product Applications

UltraShield HY 17 is suitable for both interior and exterior applications for use as a Waterproofing and Protective coating of the following structures:

• Exposed roofs both flat and sloped
• Terraces, balconies, domes and patios
• Metal profile roofs and asbestos roofs
• Corrugated metal sheets and aluminum sandwich panels
• Wet areas such as toilets, kitchens and public showers
• Vertical & Horizontal exposed concrete surfaces

Features

Ready-to-Use Product Features

Abrasion Resistant,

Chemical Resistant,

Excellent Crack Bridging Ability,

Excellent Toughness,

Good Elongation,

Good Weather Stability,

Heat Resistance,

High Durability,

High Tensile Strength,

Highly Flexible,

Low VOC,

Moisture Resistant,

Resilient,

UV Resistant,

Water Resistant,

Water-based,

Waterproofing,

Easy To Apply

Features & Benefits

Product Features

• Tough yet highly flexible.
• Excellent durabilty.
• Resistant to UV and weathering effects and does not lose its properties over time
• Low VOC and free from coal tar and hazardous ingredients
• High tensile strength and elongation
• Excellent crack bridging ability
• Bonds very well to concrete and most other substrates
• Moisture and Water resistant
• High heat & solar resistance
• Abrasion resistant
• Easy to apply

Packaging & Availability

Regional Availability

• India/MiddleEast/Africa (IMEA)

Packaging Information

20Kg Pail

Physical Properties

Physical Form

Liquid

Appearance

White/Grey/Black vicious liquid

Properties

Specifications

	Value	Units	Test Method / Conditions
Application Temperature	10 - 50	°C	-
Coverage Rate	0.85	kg/m²	-
Crack Bridging Ability	1.5	mm	BS 12390
Density	1.24 - 1.34	g/cc	-
Dry Film Thickness (dry)	0.8	mm	-
Elongation at Break	min. 400	%	ASTM D 412
Final Cure	7	days	-
Hardness	50 - 60	Shore A	ASTM D 412
Initial Cure	12 - 24	hours	ASTM E 1980
Low Temperature Flexibility	-5	°C	ASTM C836
Service Temperature	-5 to 70	°C	-
Solar Reflective Index (white, solar)	min. 115	-	UEAtc
Solid Content	61 - 65	%	ASTM D 1475
Tensile Strength	min. 3.0	N/mm²	ASTM D 1644

Appearance

White/Grey/Black vicious liquid

Storage & Handling

Storage Conditions

• The material in unopened conditioned shall be stored on pallets in a cool and shaded area and should be protected from extreme climatic conditions.
• The shelf life is 12 months when stored as per recommendation and in un-opened conditions.

Shelf Life

12 months