Cyberbond CB TM 66
1 of 68 products in this brandRTU Product Type: 1K (1 component) Adhesive, Anaerobic Adhesive, Thread Locker
Application Area: Bearings, Fasteners, Thread
Compatible Substrates & Surfaces: Aluminum, Brass, Copper, Galvanized Steel, Metal, Stainless Steel, Steel
Chemical Family: Dimethacrylates
Features: Alcohol Resistant, Good Solvent Resistance, High Strength, Medium Viscosity
Enhanced TDS
Identification
- Chemical Family
- GBU
- RTU Product Type
- Categories
-
Applications
- Application Area
- Compatible Substrates & Surfaces
Applications & Uses
- Clean Surface
-
The surface condition of the mating parts has an enormous influence on the success of a bond. To achieve good bonding success the mating parts should be clean. A certain amount of e.g. oil can be tolerated.
Features
- Ready-to-Use Product Features
Features & Benefits
- Labeling Claims
- General Information about Anaerobic Adhesives
-
Anaerobic adhesives and sealants cure by means of metal contact and/or due to the absence of air. Due to these facts they are only suitable for bonding and sealing metals. Therefore, as such they are not traditional adhesives as commonly known, but are specifically good for the bonding of metal cylindrical parts where torsion-load and shearing-load play an important part. Furthermore, anaerobics are excellent sealants for threads and flanges. Anaerobis are solvent free, one component adhesives. There are active metals (construction steel, tool steel, free cutting steel, brass, copper) and inactive metals (high alloyed or stainless steel, aluminum, electroplated surfaces, cast iron). While products used on active metals cure very fast, the same products need longer times to cure when used on inactive metals. But this does not influence the intended strength.
Identification & Functionality
- Base Compound (Monomer)
-
Dimethacrylate
Packaging & Availability
- Regional Availability
Properties
- Application Temperature:
-
-50~150 °C
- Density:
-
1100 kg/m³
- Gap Fill:
-
0.0019685~0.0059055 inches
- Shelf Life:
-
12 months
- Specific Gravity:
-
1.1
- Viscosity:
-
500~800 cps
- Physical Properties
-
Value Units Test Method / Conditions Compressive Shear Strength (on steel pins/collars, polymer) 18 - 28 N/mm² - Cure Time (full, polymer) 24 hours - Density (at 20°C, monomer) 1.1 g/cm³ - Gap Filling Capacity (monomer) 0.05 - 0.15 mm - Set Time (at 23°C, M10 brass bolt/nut) 10 - 30 seconds - Temperature Range (polymer) -50 to 150 °C - Viscosity (at 20°C, 160 s⁻¹) 500 - 800 mPa.s Cone-Plate Viscometer - Typical Properties
-
Value Units Test Method / Conditions Storage Temperature 8 - 21 °C -
Regulatory & Compliance
- Certifications & Compliance
- Specification
-
- NSF S6 registered (No: 161206). This product is acceptable for use as a sealant or threadlocker in food processing facilities. It must only be used in a manner as to ensure it will have neither direct nor indirect contact with food or potable water.
- German drinking water approval: Conformity of formulation with the reference formulation of the German Environmental Agency.
Safety & Health
- Safety Information
-
- Keep the workplace clean and use in well ventilated areas only. Installll suitable exhaust system at the workplace.
- Wear suitable safety glasses and gloves.
Storage & Handling
- Storage Conditions
-
Store products in a cold and dark place. Optimal storage temperature range is between 8 °C - 21 °C.
- Shelf Life
-
12 months (at 20°C in unopened bottles, monomer)
Technical Details & Test Data
- Property Details & Graph
-
Temperature resistance Tested at temperature
Adhesive performance Tensile shear strength
Substrate, Result N/mm² Adhesive strength (Steel) 20 to 28 Adhesive strength (Stainless steel V2A) 16 to 24 Adhesive strength (Galvanized steel) 12 to 24 Adhesive strength (Brass) 14 to 26 Breakloose torque
Solvent resistance
Solvent Example Resistance alcohols ethanol, methanol, isopropyl alcohol Ok esters ethylacetate, benzoic benzyl ester, Ok other liquids water, freon, diesel oil Ok other liquids ammonium hydroxide, bromine, hydrobromic acid, lithium hydroxid, perchloric acid, potassium hydroxide Limited gasses acetylene, argon, butane, ethane,nitrogen Ok gasses ammonia, freon gas, oxygen (pure and /or oxygen rich systems), chlorine Limited Measurement of Viscosity
Viscosity describes the flow-ability of a liquid. Cyberbond measures the viscosity of the products by means of the cone/plate method: the liquid is applied on a panel and a defined cone presses the liquid together and rotates. You differentiate between a Newtonian and a thixotropic liquid. In terms of a Newtonian liquid you will get a relative constant viscosity graph in dependence of the rotary speed of the cone. In terms of thixotropic liquids the product becomes more liquid (down to its base viscosity) the faster the cone rotates. The viscosity is measured in mPa*s